Plumber's Essentials: Your Key to Bathtub Installation
Plumber's Essentials: Your Key to Bathtub Installation
Blog Article
This article down below on the subject of How to Install a Bathtub is amazingly engaging. You should keep reading.
Installing a bathtub isn't precisely rocket science, but it does call for solid plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old bath tub with a new one is also a moderately hard job. If the old tub is conveniently obtainable, the job can move quickly; if you need to open a wall to get rid of the old tub and also position the new tub, the job is much harder. In either situation, the task is within a house handyman's skills, although you will require an assistant to move out the old tub and embeded in the brand-new one. Make sure you have actually certified yourself for the job and fit attempting it. Instead of working with a service provider to take control of a halfway-completed project, it is far better to think about utilizing one prior to you begin. Possibilities are you might need an expert plumber to make tube connections.
This short article will certainly assist you set up a brand-new bathtub in your washroom if you have currently bought a new bathtub as well as don't require to transform the arrangement of your previous water supply pipelines.
Your tools and product list need to make up the following:
Getting ready for the Installment
First of all, the sustaining frame provided with the bath needs to be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is essential to see to it that if the faucet comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the versatile faucet connectors to the bottom of the two taps using 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you utilize all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must currently prepare to be fitted in its last setting.
Removing Old Taps
If you require to change old faucets with new ones as a part of your installment, then the first thing you ought to do is disconnect the water supply. After doing so, activate the taps to drain pipes any water staying in the system. The process of eliminating the existing taps can be fairly troublesome due to the restricted accessibility that is frequently the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the taps. Have a cloth ready for the continuing to be water that will come from the pipelines. Once the supply pipelines have been eliminated, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the solitary taps from turning throughout this procedure. When the taps have been removed, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Before proceeding to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Using both wooden boards under its feet, put the bathtub in the needed placement. The wood boards are helpful in equally spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 little factors.
The next objective is to make certain that the bathtub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bathtub till the level reviews degree.
To mount taps, fit all-time low of the outermost flexible tap adapter to the suitable supply pipe by making a compression sign up with; after that do the exact same for the various other faucet.
Activate the water supply as well as inspect all joints and brand-new pipework for leakages as well as tighten them if required. Fill the bath tub as well as also examine the overflow outlet and also the normal outlet for leakages.
Lastly, fix the bath paneling as described in the manufacturer's user's manual. Tiling as well as securing around the bathtub needs to wait till the bath tub has been made use of at the very least once as this will certainly resolve it right into its final setting.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will need decreasing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin making sure that the washers remain in place between the tap and the sink. Safeguard the faucet in position with the manufacturer offered backnut. Once the faucet is securely in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical tap ports. The former kind should be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to fracture a rigid seal, causing the water to pass through the wall in between the bathroom and also the tiling, bring about issues with wetness and also possible leakages to the ceiling below.
You can choose from a range of coloured sealers to blend in your fixtures and installations. They are marketed in tubes as well as cartridges, and are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked newspaper or soft rope. Remember to always fill the bath tub with water prior to sealing, to permit the motion experienced when the bathtub remains in usage. The sealant can crack fairly very early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise conveniently offered on the marketplace. It is recommended to fit the floor tiles making use of waterproof or waterproof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I have been very fascinated by How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I'm hoping you enjoyed my blog post. Kindly take the opportunity to share this write-up if you liked it. Thanks for your time. Visit again soon.
Secure your plumbing. Report this page